J'aimerais savoir comment on utilise isapnp
car j'ai une carte son isa home studio pro 64
non detectée sous mandrake 9.0
 
j'ai fait un pnpdump -a isa.conf
mais je sais pas comment finir la config de ma carte
 
 

sndconfig ne marche pas ?

non du moins j'ai pas réussi
pourtant il a bien un type de carte correspond
mais il trouve rien

J'ai eu récement ce prob avec ma sb16.
Il trouvait et un jour plus rien.
Je l'ai enlevée puis remise et hop j'ai du son.
Depuis je croise les doigts.

vala ce que me sort pnpdump
sma l'air vu que c'est compliqué
 
ensuite je dois décommenter les lignes correspondantes
à la config que je veuc faire mais j'en fait quoi ensuite de ce fichier ????
 
# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
#  
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#  
# For details of the output file format, see isapnp.conf(5)
#  
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#  
# Compiler flags:  -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#  
# Trying port address 0273
# Board 1 has serial identifier 27 ff ff ff ff 68 18 73 16
 
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
 
# Card 1: (serial identifier 27 ff ff ff ff 68 18 73 16)
# Vendor Id ESS1868, No Serial Number (-1), checksum 0x27.
# Version 1.0, Vendor version 1.0
# ANSI string -->Maxi Sound 64 Series<--
#
# Logical device id ESS8600
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
 
(CONFIGURE ESS1868/-1 (LD 0
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0800
#         Maximum IO base address 0x0ff8
#         IO base alignment 8 bytes
#         Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0800))
 (NAME "ESS1868/-1[0]{Maxi Sound 64 Series}" )
# (ACT Y)
))
#
# Logical device id ESS8601
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
 
(CONFIGURE ESS1868/-1 (LD 1
 
# Multiple choice time, choose one only !
 
#     Start dependent functions: priority preferred
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 0 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Fixed IO base address 0x0220
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Fixed IO base address 0x0388
#             Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
#       Fixed IO base address 0x0300
#             Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
 
#       Start dependent functions: priority acceptable
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 0 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
#       IRQ 5, 7, 10 or 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Fixed IO base address 0x0388
#             Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
#       Fixed IO base address 0x0300
#             Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
 
#       Start dependent functions: priority acceptable
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
#       IRQ 5, 7, 9, 10, 11 or 12.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Fixed IO base address 0x0388
#             Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 16 bytes
#             Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
 
#       Start dependent functions: priority acceptable
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
#       IRQ 5, 7, 9, 10, 11 or 12.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Fixed IO base address 0x0388
#             Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0800
#             Maximum IO base address 0x0ffe
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0800))
 
#       Start dependent functions: priority functional
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
#       IRQ 5, 7, 9, 10, 11 or 12.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0800
#             Maximum IO base address 0x0ffc
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0800))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0800
#             Maximum IO base address 0x0ffe
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0800))
 
#     End dependent functions
 (NAME "ESS1868/-1[1]{Maxi Sound 64 Series}" )
# (ACT Y)
))
#
# Logical device id ESS8602
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
 
(CONFIGURE ESS1868/-1 (LD 2
 
# Multiple choice time, choose one only !
 
#     Start dependent functions: priority preferred
#       Fixed IO base address 0x0201
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0201))
 
#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x020f
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0200))
 
#     End dependent functions
#     Compatible device id PNPb02f
 (NAME "ESS1868/-1[2]{Maxi Sound 64 Series}" )
# (ACT Y)
))
#
# Logical device id ESS8603
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
 
(CONFIGURE ESS1868/-1 (LD 3
 
# Multiple choice time, choose one only !
 
#     Start dependent functions: priority preferred
#       IRQ 9.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 9 (MODE +E)))
#       Fixed IO base address 0x0330
#             Number of IO addresses required: 6
# (IO 0 (SIZE 6) (BASE 0x0330))
 
#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9, 10, 11 or 12.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0ff0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 6
# (IO 0 (SIZE 6) (BASE 0x0330))
 
#     End dependent functions
 (NAME "ESS1868/-1[3]{Maxi Sound 64 Series}" )
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
 
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)

A confirmer mais quand tu fait sndconfig et que ça ne marche pas.
Il te propose de rentrer les params à la main.
A mon avis ensuite il décommente lui même les lignes concernées.
Donc si tu connais les params irq,dma,etc.... tu le fait direct.
Je répète à confirmer.

ok c fait mais snd config me mets une message
pas de sb.o.gz
modprobe sound-slot-0 failed
 
je dois pas avoir les pilotes

Si peut être mdk m'as fait le même coup et en fin de compte c'était un prob hardware.
Quand tu as installé mdk qu'à tu répondu à la question possédez vous une carte son isa?

J'ai moi même récupéré un PC à l'interieur duquel on trouve une SB16 ISA. Je n'ai pas encore choisi la distribution que je souhaitais installer et ne savais pas si mon materiel faonctionnerait complètement.  
 
C'est pourquoi, avant toute chose, j'ai gravé le CD live KNOPPIX. Cette "distrib", une fois démarrée, fait fonctionner la carte son à merveille. Je peux par la même occasion voir quel driver est utilisé  
 
 
PS: je ne sais pas si cela sera suffisant, mais le fait de pouvoir voir la config qui fonctionne "en live" devrait t'aider.

Les sb16,sb32 fonctionnent bien du moins sur mdk.

je l'ai knoopix mais il la detecte pas non plus

 
alors qu'avec une mandrake 7.2 elle fonctionnait
je vais quand même tester sndconfig sous knoppix pour voir

J'ai voulu installé ma sb32 à la place de ma sb16, résultat comme toi prob avec sb.o.gz.      

Me revoila avec toujours mon pb
juste un truc en plus il semblerait que le pb
vienne de la config contenu dans isapnp.conf
 
help !!!!!!!!!!!!!!!!!!!!

C'est pas moi qui vais pouvoir t'aider vu que sur 3 carte son je n'arrive à en faire fonctionner q'une seule.
sb16=ok
sb32= niet
als4000= niet
 
Aller courage.  

colles quand même ton isapnp.conf
ça pourrait me donner une base
 
savoir si le mien est cohérent  

Il ne doit pas servir car il est tout commenté et pourtant ma sb16 fonctionne en ce moment(sauf pour les cd,dvd bien sûr ).

quelqu'un d'autre peut être alors qui aurais une carte son isa
pourrait coller son isapnp.conf ça serait cool

 
 
bon on est pas les deux seuls à utiliser une carte son isa ici

Faut croire que si.

bourdel