modprobe snd-hda-intel model=fujitsu

758   Module snd-hda-intel
759   --------------------
760  
761     Module for Intel HD Audio (ICH6, ICH6M, ESB2, ICH7, ICH8),
762   ATI SB450, SB600, RS600,
763   VIA VT8251/VT8237A,
764   SIS966, ULI M5461
765  
766     model - force the model name
767     position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
768     probe_mask  - Bitmask to probe codecs (default = -1, meaning all slots)
769     single_cmd  - Use single immediate commands to communicate with
770   codecs (for debugging only)
771     enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
772     power_save - Automatic power-saving timtout (in second, 0 =
773   disable)
774     power_save_controller - Reset HD-audio controller in power-saving mode
775   (default = on)
776  
777     This module supports one card and autoprobe.
778  
779     Each codec may have a model table for different configurations.
780     If your machine isn't listed there, the default (usually minimal)
781     configuration is set up.  You can pass "model=<name>" option to
782     specify a certain model in such a case.  There are different
783     models depending on the codec chip.
784  
785    Model name Description
786    ----------    -----------
787  ALC880
788    3stack 3-jack in back and a headphone out
789    3stack-digout 3-jack in back, a HP out and a SPDIF out
790    5stack 5-jack in back, 2-jack in front
791    5stack-digout 5-jack in back, 2-jack in front, a SPDIF out
792    6stack 6-jack in back, 2-jack in front
793    6stack-digout 6-jack with a SPDIF out
794    w810  3-jack
795    z71v  3-jack (HP shared SPDIF)
796    asus  3-jack (ASUS Mobo)
797    asus-w1v ASUS W1V
798    asus-dig ASUS with SPDIF out
799    asus-dig2 ASUS with SPDIF out (using GPIO2)
800    uniwill 3-jack
801    fujitsu Fujitsu Laptops (Pi1536)
802    F1734  2-jack
803    lg  LG laptop (m1 express dual)
804    lg-lw  LG LW20/LW25 laptop
805    tcl  TCL S700
806    clevo  Clevo laptops (m520G, m665n)
807    test  for testing/debugging purpose, almost all controls can be
808    adjusted.  Appearing only when compiled with
809    $CONFIG_SND_DEBUG=y
810    auto  auto-config reading BIOS (default)
[...]
1018  
1019     The model name "genric" is treated as a special case.  When this
1020     model is given, the driver uses the generic codec parser without
1021     "codec-patch".  It's sometimes good for testing and debugging.
1022  
1023     If the default configuration doesn't work and one of the above
1024     matches with your device, report it together with the PCI
1025     subsystem ID (output of "lspci -nv" ) to ALSA BTS or alsa-devel
1026     ML (see the section "Links and Addresses" ).
1027  
1028     power_save and power_save_controller options are for power-saving
1029     mode.  See powersave.txt for details.
1030  
1031     Note 2: If you get click noises on output, try the module option
1032      position_fix=1 or 2.  position_fix=1 will use the SD_LPIB
1033      register value without FIFO size correction as the current
1034      DMA pointer.  position_fix=2 will make the driver to use
1035      the position buffer instead of reading SD_LPIB register.
1036      (Usually SD_LPLIB register is more accurate than the
1037      position buffer.)
1038  
1039     NB: If you get many "azx_get_response timeout" messages at
1040     loading, it's likely a problem of interrupts (e.g. ACPI irq
1041     routing).  Try to boot with options like "pci=noacpi".  Also, you
1042     can try "single_cmd=1" module option.  This will switch the
1043     communication method between HDA controller and codecs to the
1044     single immediate commands instead of CORB/RIRB.  Basically, the
1045     single command mode is provided only for BIOS, and you won't get
1046     unsolicited events, too.  But, at least, this works independently
1047     from the irq.  Remember this is a last resort, and should be
1048     avoided as much as possible...
1049      
1050     MORE NOTES ON "azx_get_response timeout" PROBLEMS:
1051     On some hardwares, you may need to add a proper probe_mask option
1052     to avoid the "azx_get_response timeout" problem above, instead.
1053     This occurs when the access to non-existing or non-working codec slot
1054     (likely a modem one) causes a stall of the communication via HD-audio
1055     bus.  You can see which codec slots are probed by enabling
1056     CONFIG_SND_DEBUG_DETECT, or simply from the file name of the codec
1057     proc files.  Then limit the slots to probe by probe_mask option.
1058     For example, probe_mask=1 means to probe only the first slot, and
1059     probe_mask=4 means only the third slot.
1060  
1061     The power-management is supported.